We are striving to achieve complete self-sufficiency in power networks by localizing the technology for manufacturing key components in the electricity distribution industry, aiming to improve this sector
Pig tail
Pigtail is a piece of rebar with hot galvanized plating or dichromate plating, which has a wire in the shape of a hook at the end. Pig tail is made of ST37, CK10, ST1008, ST1010. This product is available in sizes 230*14-260*14-300*14-360*14-400*14 and 230*16-260*16-300*16. 360*16-400*16-450*16 are available. The pig tail is a piece of rebar with hot galvanized plating or dachromat plating, which has a wire in the shape of a hook at the end. Pig tail is made of ST37, CK10, ST1008, ST1010. This product is available in sizes 230*14-260*14-300*14-360*14-400*14 and 230*16-260*16-300*16. -360*16-400*16-450*16 are available
Double-threaded bolt with a thick back
This bolt is used for installing equipment on poles in a double configuration. For example, it is used for securing the underframe of a transformer or for doubling a cross arm. The material is wire made of ST37, CK10, ST1008, and ST1010, with a hot-dip galvanized coating. This product is available in sizes: 300*16, 360*16, 400*16, 450*16, 500*16, 550*16,600*16
One-end bolt and nut
These bolts and nuts are used to secure equipment that is directly attached to power poles. The bolts are made of ST37, CK10, ST1008, and ST1010 steel. The screw heads are forged, and the ends of the bolts are threaded through a rolling method after extrusion. This product is available in sizes 40*14, 50*14, 120*14, 230*14, 260*14, 300*14, 360*14, 40*16, 50*16, 230*16, 260*16, 300*16, 360*16, 400*16
Branching science
Alamek produces single-phase and three-phase electricity with insulating equipment (approved by Tawanir company)
Naali Forge
This part is used in the non-electrical connections of the conductor carrying the electric current to the base and holder
Shegel (U shape forge)
It is one of the fittings of the power distribution network, which is used to create connections between conductors and pylons
Aluminum jumper clamp
Aluminum jumper clamp (connector) is used for branching from electric networks or for jumping at the end of the connection to the electric pole. This product is available in 70 and 120 sizes
Steel earth pipe clamp
The earth clamp is used to connect the wires to the earth bar and earth bars
Three-bolt harness clamp
The harness clamp is made of two pieces of st37 steel belt, which is connected by three 16 bolts. Harness clamp is used to fasten (connect) harness wire to harness rod, harness insulator and harness eye bolt. This product is available in size 12
Restraint and adjustment belt
The steel buffer belt is used at the top and bottom of the installation crossarm and also for the installation of the trans platform grade 12-10-8
Silicone pole insulator base
The base of the silicone beam insulator is made of studs and is specially designed for connecting to the insulator and has the necessary holes to connect to the beam, which is produced and offered in lengths of 55, 45 and 75 cm.
Complementary stud
Complementary studs are used to transfer fittings to round concrete beams
Single base trans platform
Trans single base platform is one of the best and most suitable platforms for related environments. This platform has a hot galvanized coating
Trans platform
The transformer platform or the console for installing the transformer is a metal artifact that is used to install the aerial transformer on the base (power pole). A transformer is an electrical device designed and built to increase or decrease voltage. This product is available in sizes 8-10-12 in the form of six pieces
Coat-out platform
In 20 kV medium pressure lines, rectangular and cube-shaped platforms are used, which are made of iron with hot galvanized coating, so that the cutouts do not touch or connect to concrete or wooden beams
Brace
One of the fittings is the power distribution network, which is used to increase the stability of the cross arm and is placed between the cross arm and the middle of the beam
Light arm
The light arm is used to hold and keep the lights fixed on the poles. These components are also known as lamp arm, lamp head or lamp base, they play an important role in the street lighting system. This product is available in dimensions of 60 cm and 1-1/5-2-3 meters
Cross arm
The cross arm (console) is used to keep the wires and insulators on the beam. Cross Arm is a type of console in the form of a cross arm with a base, which is widely used in distribution networks. This product is available in sizes 1/2-8, 1/5-8, 2-8, 2/40-8, 3- 8 and 1/2-10, 1/5-10, 2-10, 2/40-10, 3-10 are available
5 insulators
In order to keep the horizontal privacy of low pressure lines and to maintain the distance of the line to the buildings and balconies of the houses, the lifting arm is used. This product is available in 50 and 80 cm sizes
Self-retaining cable carrying handle
It is used to distance power grids from power poles and respect the privacy of power networks and is installed on concrete power poles
Earth bar
The earth rod and its connections are used as an intermediary to the ground in all types of soil conditions to create a suitable earthing system in underground and aerial electricity distribution and transmission networks. This product is available in 1/5 and 3 sizes. meter is available
Harness earrings
The harness earring is a metal piece that is used in the structure of the harness masts and towing wires. The earring is a metal piece that is used to prevent the harness wire from bending strongly in the harness ring and cutting it
Restraining rod
The mooring rod is one of the accessories of the mooring mast. In general, restraining masts are considered structures that are used in many industries
Restraint page
The aerial power distribution network always needs protection measures due to passing through different regions and locations. Installing a harness is one of the ways to protect the air network. The material of this plate is st37 steel and sheet. This product is available in size 50*50*5
Type K thermocouple
This type of temperature sensors are widely used in various industries and are among the most widely used sensors. This type of sensor has aluminum alloy for the positive base and chromel alloy for the negative base. Alumel is an alloy made primarily of nickel and containing (small amounts) of aluminum, silicon, and manganese. The temperature range in this type of heating pairs is from -270 to +1372 degrees Celsius. The standard color of these sensors is red (negative) and yellow (positive)
Type J thermocouple
It uses iron alloy as positive base and Constantan alloy as negative base. These types of thermometers or thermocouples are used in oxide environments and vacuum environments easily and without any problems. Type J thermocouples should be inspected every once in a while, as their iron base may corrode. The temperature range of this type of sensor is from -270 to +1200 degrees Celsius and its standard color is red (negative) or white (positive)
Type E thermocouple
Type E is made of nickel-chromium and constantan. With a wide temperature range from -270°C to +1000°C. They have limited use in vacuum environments or reducing atmospheres. They also have the highest EMF change at any degree
Type B thermocouple
This type of sensors are used at very high temperatures and are able to measure at high temperatures without the slightest problem. It can be said that among the sensors based on noble metals, it has the highest temperature limit and its stability is very extraordinary. Its temperature range is 0 to 1820 degrees Celsius
Type T thermocouple
In this type of thermocouples, it consists of copper (positive base) and constantan (negative base) alloys. The temperature range of this type is from -270 to +400 degrees Celsius and their color code is red (negative) and blue (positive)
Type N thermocouple
N-type temperature measuring thermometer consists of nickel-chromium alloys as (positive base) and nickel, nickel, silicon and magnesium as (negative base). The temperature range of this type is from -270 to +1300 degrees Celsius and its standard color code is red (negative) and orange (positive)
Type P thermocouple
P-type is another type of sensor based on noble metals, which has a similar curve to K-type at high temperatures and can be used in oxide environments with a temperature range of up to 1260 degrees Celsius
Type S thermocouple
Type S is known for its high precision and stability. This type is used for applications that require high temperature. Biotechnology and pharmaceutical industries are among the industries that use this type widely. The temperature range of this sensor is from -50 to 1750 degrees Celsius
Type R thermocouple
This type is intended for use in high temperatures and is very similar to S type. The rhodium percentage of this type is higher than that of S type. That is why it is more expensive. Type R has the same performance as type S and can be used for low temperature applications due to its stability and high accuracy. It has a temperature range of -50 to 1768 degrees Celsius
